Engine Rebuild Kit Honda GL1000 Gold Wing LTD 1975-1979 with Rings + Oil Seals
If you're diving in and doing a rebuild, replacing engine cover gaskets and replacing seals this is a great kit to have on hand! The piston rings are for the stock bore. 12251-371-003 - Cylinder Head Gasket - x2 12328-371-000 - Valve Cover Gasket - x2 11831-371-010 - Right Front Cover Gasket - x1 11832-371-010 - Left Front Cover Gasket - x1 30376-371-306 - Breaker Gasket - x2 12391-371-306 - Cover Gasket - x1 19429-371-306 - Water Joint Gasket - x2 11372-371-306 - Final Gear Cover Gasket - x1 11391-371-306 - Transmission Cover Gasket - x1 11393-371-306 - Clutch Cover Gasket - x1 11394-371-306 - Rear Crankcase Gasket - x1 11396-371-306 - Water Pump Gasket - x1 15128-371-000 - Oil Passage Gasket - x1 15229-371-000 - Clutch Oil Pump Gasket - x1 30379-463-306 - Pulser Cover Gasket - x1 18291-286-306 - Exhaust Gasket - x4 12209-MB9-003 - Valve Stem Seal - x8 91303-371-000 - Oil Strainer Gasket - x1 91301-371-005 - O-Ring 40X2.6 - x4 91301-MB6-003 - O-Ring 21.9X2.3 - x4 91305-371-003 - O-Ring 6.5X1.5 - x2 91307-PH7-660 - O-Ring 13.5X1.4 - x1 91307-PH9-000 - O-Ring 15.5X1.4 - x1 91259-333-000 - O-Ring 9.5X1.7 - x1 91302-001-020 - O-Ring 30.8x3.2 - x1 91304-HB3-003 - O-Ring 33.5X3.0 - x1 91302-377-000 - O-Ring 15X2.5 - x2 91305-426-003 - O-Ring 46X2 - x1 91316-425-003 - O-Ring 89X4.5 - x1 91318-500-000 - O-Ring 27X2.7 - x1 91303-634-010 - O-Ring 12.5X2.2 - x1 91306-371-003 - O-Ring 18x3 - x1 91307-703-000 - O-Ring 25.4X2.4 - x1 91333-567-010 - O-Ring 17x2.5 - x2 91361-706-000 - O-Ring 8x1.9 - x2 91302-317-700 - O-Ring 54x2 - x1 91356-706-000 - O-Ring 56x2.4 - x1 91345-580-000 - O-Ring 29x2.2 - x1 91301-283-005 - O-Ring 5x2.4 - x1 91309-283-005 - O-Ring 42.5x2 - x1 91354-702-000 - O-Ring 23 - x1 91301-MB6-003 - O-Ring 21.9x2.3 - x2 91319-300-000 - O-Ring 13x2.5 - x1 91308-371-003 - O-Ring 4.1x2.5 - x2. Cylinder Head Seal - Quantity 3 Tachometer Seal Oil Pump Seal 1 Oil Pump Seal 2 Clutch Cover Seal Rear Case Cover - Small Seal Rear Case Cover - Large Seal Cylinder Block Seal Crankshaft Seal.
Press your seals in straight with a seal driver or a socket with a slightly smaller OD than the seal. Both surfaces must be free of dirt to create an oil tight seal. All sealing surfaces for gaskets must be clean and flat to make a proper seal, sometimes non-hardening sealant is necessary. Be very careful when installing the cylinder over new rings, it's helpful to have the proper tool to keep the rings compressed as you lower the cylinder over the pistons.
Try to use only plastic tipped tools to prevent from scratching aluminum surfaces. The Letter stamped on the top two rings should be facing up when installing them and stagger the ring gaps according to the manual.
Top Compression Ring (silver outer rim). Second Ring (black outer rim).
Bottom Rings (3 pieces - Spacer in the middle - 1 thin ring on either side). This item is in the category "eBay Motors\Parts & Accessories\Motorcycle & Scooter Parts & Accessories\Engines & Engine Parts\Gaskets, Seals & Kits". The seller is "4into1motorcycleparts" and is located in this country: US. This item can be shipped worldwide.
- Country/Region of Manufacture: Taiwan
- Custom Bundle: Yes
- Manufacturer Part Number: ERK-10B
- Brand: Engine Rebuild
- Bundle Description: Includes all parts shown and described.